% This is CMSY24.MF in text format, as of August 25, 1986. % Computer Modern Math Symbols 24 point if unknown cmbase: input cmbase fi font_identifier:="CMSY"; font_size 24pt#; u#:=46.7/36pt#; % unit width width_adj#:=0pt#; % width adjustment for certain characters serif_fit#:=0pt#; % extra sidebar near lowercase serifs cap_serif_fit#:=11.7/36pt#; % extra sidebar near uppercase serifs letter_fit#:=0pt#; % extra space added to all sidebars body_height#:=648/36pt#; % height of tallest characters asc_height#:=600/36pt#; % height of lowercase ascenders cap_height#:=590/36pt#; % height of caps fig_height#:=556.8/36pt#; % height of numerals x_height#:=372/36pt#; % height of lowercase without ascenders math_axis#:=216/36pt#; % axis of symmetry for math symbols bar_height#:=208.8/36pt#; % height of crossbar in lowercase e comma_depth#:=168/36pt#; % depth of comma below baseline desc_depth#:=168/36pt#; % depth of lowercase descenders crisp#:=8/36pt#; % diameter of serif corners tiny#:=8/36pt#; % diameter of rounded corners fine#:=7/36pt#; % diameter of sharply rounded corners thin_join#:=13.7/36pt#; % width of extrafine details hair#:=19.4/36pt#; % lowercase hairline breadth stem#:=54/36pt#; % lowercase stem breadth curve#:=67/36pt#; % lowercase curve breadth ess#:=54.5/36pt#; % breadth in middle of lowercase s flare#:=76/36pt#; % diameter of bulbs or breadth of terminals dot_size#:=89/36pt#; % diameter of dots cap_hair#:=26.4/36pt#; % uppercase hairline breadth cap_stem#:=69/36pt#; % uppercase stem breadth cap_curve#:=82.68/36pt#; % uppercase curve breadth cap_ess#:=79/36pt#; % breadth in middle of uppercase s rule_thickness#:=.9pt#; % thickness of lines in math symbols dish#:=1/36pt#; % amount erased at top or bottom of serifs bracket#:=48/36pt#; % vertical distance from serif base to tangent jut#:=72/36pt#; % protrusion of lowercase serifs cap_jut#:=88/36pt#; % protrusion of uppercase serifs beak_jut#:=23.4/36pt#; % horizontal protrusion of beak serifs beak#:=168/36pt#; % vertical protrusion of beak serifs vair#:=16.9/36pt#; % vertical diameter of hairlines notch_cut#:=24pt#; % maximum breadth above or below notches bar#:=26.4/36pt#; % lowercase bar thickness slab#:=26.4/36pt#; % serif and arm thickness cap_bar#:=26.4/36pt#; % uppercase bar thickness cap_band#:=26.4/36pt#; % uppercase thickness above/below lobes cap_notch_cut#:=24pt#; % max breadth above/below uppercase notches serif_drop#:=9.6/36pt#; % vertical drop of sloped serifs stem_corr#:=1/36pt#; % for small refinements of stem breadth vair_corr#:=1/36pt#; % for small refinements of hairline height apex_corr#:=0pt#; % extra width at diagonal junctions o#:=18.6/36pt#; % amount of overshoot for curves apex_o#:=18.6/36pt#; % amount of overshoot for diagonal junctions slant:=.25; % tilt ratio $(\Delta x/\Delta y)$ fudge:=.8; % factor applied to weights of heavy characters math_spread:=0; % extra openness of math symbols superness:=1/sqrt2; % parameter for superellipses superpull:=1/6; % extra openness inside bowls beak_darkness:=11/30; % fraction of triangle inside beak serifs ligs:=2; % level of ligatures to be included square_dots:=false; % should dots be square? hefty:=false; % should we try hard not to be overweight? serifs:=true; % should serifs and bulbs be attached? monospace:=false; % should all characters have the same width? variant_g:=true; % should an italic-style g be used? low_asterisk:=false; % should the asterisk be centered at the axis? math_fitting:=true; % should math-mode spacing be used? % the following font parameters are explained in {\sl The \TeX book}, Appendix G subs:=18/24; % subscripts to 10pt will normally be in 7pt type rth#:=.4pt#; % assume that rules will come from cmex10 fontdimen 8: % parameters $\sigma_8$ through $\sigma_{22}$ will now be listed math_axis#+3.51rth#+96/36pt#+subs*desc_depth#, % num1 math_axis#+1.51rth#+71/36pt#, % num2 math_axis#+1.51rth#+114.6/36pt#, % num3 -(math_axis#-3.51rth#-subs*fig_height#-296/36pt#), % denom1 -(math_axis#-1.51rth#-subs*fig_height#-71.9/36pt#), % denom2 20.56pt#-subs*asc_height#, % sup1 19.48pt#-subs*asc_height#, % sup2 248/36pt#, % sup3 96/36pt#, % sub1 -(19.17pt#-2subs*asc_height#-3.1rth#), % sub2 subs*asc_height#-36/36pt#, % sup\_drop 18/36pt#, % sub\_drop 23.9pt#, % delim1 24.1pt#, % delim2 math_axis#; % axis\_height generate mathsy % switch to the driver file